New TJ Products from Artec Industries !

Artec

Supporting Vendor
That's Right , NEW TJ PRODUCTS !!!! We haven't forgot about the TJ guy's .



tj2016b.jpg
Stock Trackbar Bracket Replacement for TJ Front Axle
This heavy bracket is designed to replace the weak factory trackbar bracket on the front 30 and Rubicon 44 axles in the Jeep TJ, LJ, XJ, and ZJ. The factory bracket often has a wallowed out hole allowing axle shifting and is one of the major contributors to the feared DEATH WOBBLE. This bracket replaces the factory bracket for better piece of mind. The 1/4" thick CNC precision cut and formed components of this setup ensure a quality, heavy duty solution.

NOTE: This bracket is NOT bolt on and requires welding. Cutting off the factory tracbar bracket is required and welding this in it's place.

Joint width is 1.66", so use our NARROW MISALIGNMENT SPACERS with 7/8" HEIMS if you are building your own Trackbar.

Features include:

Heavy duty construction from 1/4" mild steel...won't wallow out like factory bracket.
Precision CNC laser cut and bent for great fitment.
Possible solution to fix DEATH WOBBLE.
Tab and Slots allow for perfect alignment and easy installation*
Replaces factory swaybar mount as well.
Works great with an Artec truss


tj2025a.jpg
tj2025c.jpg

TJ Aluminum Body Mount Spacer Kit

The perfect compliment to our TJ Boatside Body Mounts, these CNC machined Aluminum Spacers allow you to get a 1.25" body lift on the radiator and the four rear most body mounts if you do not already have a pre-existing body lift kit.

Features:
CNC Machined 6061 Aluminum body mount spacers
Grade 8 hardware
Works for TJs and LJs
MADE IN THE USA!

***NOTE: FOR USE ONLY WITH ARTEC TJ BOATSIDE BODY MOUNT 1.25 inch body lift***




tj2015a.jpg
tj2015b.jpg

Got the Bowing Spring Blues? Our TJ Rear Coil Correction Kit is the answer.

Our new TJ Rear Coil Correction Kit fixes a common problem on lifted Jeeps...bowing springs. The OEM spring perches were set at an angle which is great for no lift but once you start to lift your vehicle, the angles change resulting in bowing spring that can be permenantly damaged an even unseated during articulation. Our correction kit eliminated the factory angle allowing any lift height with no bowing. We even add provisions if you want to do a 1 inch stretch.

Features:
CNC Laser cut and CNC bent from 3/16" thick steel
CAD designed with models directly from Chrysler to fit perfectly
Choose between STOCK LOCATION or 1 inch STRETCH
Factory tracbar mount etched cutout
Etched alignment mark
Accepts factory jounce cup and bolt
Side specific etching
Works for TJs, and LJs and can be used in YJs for a coil conversion.
MADE IN THE USA!
 

Artec

Supporting Vendor
tj2015d.jpg



tj2010g.jpg
tj2010f.jpg
tj2010b.jpg

TJ Boatside Body Mounts

Our Boatside Body Mounts are designed to allow TJ and LJ owners to get rid of the clunky and weak body mounts that often either catch on obstacles or just plain rot off the frame. The under side of the body mount is completely boxed in and even angled to provide a skid plate which allows for less chance of the vehicle getting hung up on the mount. Plus since we incorporate the typical body lift that is installed on these Wranglers into the mount instead of relying on taller bushing, the whole mount is raised up and out of the way.

This DIY kit includes the laser cut and precision CNC bent pieces that will need to be welded together as well as on to the frame.

Rather than pay for aftermarket lift bushings, simply use normal OEM height bushings with this kit. The bushings are inserted from the back side above the frame which means the underside of the boatside doesn't need as large of a hole, giving you better clearances and less material to get hung up on.

This kit has been specifically designed to compliment the factory frame, yet look distinctly hardcore. It is also engineered for maximum strength and easy assembly with jigs and laser etched part numbers so you can't put it together wrong. Just another example of the FUSION OF FORM AND FUNCTION from Artec.

Features:
CNC Laser cut and CNC bent from 3/16" thick steel
CAD designed with models directly from Chrysler to fit perfectly
Provides 1.25" body lift which allows for additional modifications that need more room
Also available in OEM height. See related products below.
Tabs ensure proper locating of the laser cut pieces
Angled sides provide better break-over angles
Fully boxed design and bottom skidplate means you don't need to worry about whether your mounts will last the trip
ADD TJ ALUMINUM BODY MOUNT SPACER KIT IF YOU DO NOT HAVE A BODY LIFT ALREADY.
Works for TJs and LJs
MADE IN THE USA!

***NOTE: BODY LIFT VERSION Provides 1.25 inch body lift***
 
Top